HP Z600 V1 Gaming Computer

The HP Z600 V1 Workstation has all the base components to be converted in to a solid gaming computer.  HP Z600's are a dual socket Xeon based workstations.  The Z600 V1 supports up to 48GB of DDR3 memory and 2 Internal SAS/SATA Hard Drives.  It is important to note that it has an standard 600W Power Supply, which limits the Graphics Cards that you can install.  Let us show you how you can build an effective HP Z600  V1 Gaming PC.


How do I check to see if my HP Z600 is a V1 or V2?

Open your side panel and check your system board PN.

Version 1 has system board PN: 461439-001 (460840-002)

Version 2 has system board PN: 591184-001 (460864-003)


Where to buy?

If you haven't already acquired a HP Z600 Workstation we'd recommend checking out a company called Serverworlds.  They sell the Z600's cheap and they provide free ground shipping to the lower 48 states.   You can also try to snag them cheap on Ebay.  However, Ebay can be a bit of a gamble because you never know what you are going to get.

The goal is to purchase the Z600 with a good processor(s) and memory already installed and then you can source the graphics cards, hard drives, and other optional components from other sources.


What Processor(s) should I get?

High Clock speed cpu's are the way to go.

In most cases you can get by with a single processor listed below.  If you plan to stream your gaming on youtube or twitch, we recommend getting 2 processors.

Recommended Processors:

Up to 2 x 6C Xeon X5660 3.33Ghz 12MB 6.40GTs Processors | 3.60Ghz Max Turbo Frequency (SLBV6)

Up to 2 x 6C Xeon X5675 3.06Ghz 12MB 6.40GTs Processors | 3.46Ghz Max Turbo Frequency (SLBYL)


How much Memory should I get?

*The HP Z600 V1 does not support registered memory modules*

The base line should be a minimum of 16GB of memory.  However, 16GB to 32GB would be ideal.

Memory PNs:

4GB PC10600E 2Rx8 ECC Unregistered (T192H)

4GB PC12800E 2Rx8 PC3L ECC Unregistered (6DWFJ)

8GB PC12800E 2RX8 PC3 ECC Unregistered (MT18JSF1G72AZ-1G6E1ZF)

8GB PC12800E 2Rx2 PC3L ECC Unregistered (HMT41GU7AFR8A-PB)


*12800E modules will work as well, they will just clock down to 1333Mhz depending on the CPU speed*


Recommended Memory configurations:

4 x 4GB PC10600E Modules (16GB)

6 x 4GB PC10600E Modules (24GB)

4 x 8GB PC12800E Modules (32GB)

6 x 8GB PC12800E Modules (48GB)

It's very important to use 10600E modules because they will run at the max speed supported by the system board and processor.


What Hard Drive should I get?

Ideally you would want to have a Solid State Drive as your boot device as well an NVME.2 SSD to store your game libraries/large programs on.  If you are limited on budget you could go with a small SSD for your boot device and a larger capacity 7.2K SATA drive to hold your larger files/programs/games.


Recommended SSD Drives:

Samsung 860 EVO 2TB 2.5 Inch SATA III Internal SSD (MZ-76E2T0B/AM)

Samsung 860 EVO 1TB 2.5 Inch SATA III Internal SSD (MZ-76E1T0B/AM)

Samsung 860 Evo 500GB 2.5 inch SATA III Internal SSD (MZ-76E500B/AM)


Recommended large Capacity SATA Drives:

Seagate 2TB BarraCuda SATA 6 Gb/s 7200 RPM 64MB Cache 3.5 Inch Desktop Hard Drive (ST2000DM006)


*NVME.2 Drives cannot be used as a boot device with this model workstation*

NVME.2 PCIe Adapter (You need this if you plan to install an NVME.2 Drive in to this system):

NVME.2 SSD Adapter *Required to Install NVME.2*


Recommended NVME.2 SSDs:

Samsung 960 EVO Series - 500GB NVMe - M.2 Internal SSD (MZ-V6E500BW)

Samsung 970 Evo Series - 500GB NVMe -M2 Internal SSD (MZ-V7E500BW)

Samsung 960 EVO Series - 1TB PCIe NVMe - M.2 Internal SSD (MZ-V6E1T0BW)

Samsung 970 EVO Series - 1TB PCIe NVMe - M.2 Internal SSD (MZ-V7E1T0BW)


What Graphics Card should I get?

The HP Z600 has a 600W Power Supply.  This will limit your Graphics Card options.


Recommended Graphics Cards:

NVIDIA GTX 1060 6GB Graphics Card

NVIDIA GTX1660 Ti 6GB Graphics Card (takes up 3 PCI slots)

NVIDIA GTX 1070 8GB Graphics Card

NVIDIA GTX 1070 TI 8GB Graphics Card

NVIDIA RTX 2060 6GB Graphics Card

NVIDIA RTX 2070 8GB Graphics Card


What type of Monitor should I get?

Ideally it would be nice to get a monitor with a 144Hz or 244hz refresh rate or better monitor.  However, it really depends on the games you play.  If you play first person shooter games a 144hz or 240Hz or better monitor is a must.  If you play other games that do not require quick response time then a 60hz monitor should work fine.

Recommended Monitors:

ASUS PG248Q Full HD 144Hz 1MS 24" Gaming Monitor

ASUS VG278Q Full HD 1080P 144Hz 1MS 27" Gaming Monitor

ASUS XG258Q ROG Strix 24.5" 1080P 240Hz 1MS Gaming Monitor



Using the criteria above you can build a good to borderline high end gaming system using a HP Z600 Workstation.

Sample Configuration:

HP Z600 Workstation

1 x 6C Xeon X5675 3.06Ghz 12MB 6.40GTs

24GB PC10600E (6 x 4GB)

Samsung 1TB 6GBPS SSD

GTX1660 Ti w/6GB  Graphics Card

1 x 10/100/1000 Network Port

600W Power Supply


10 Pro 64Bit


We have tested this system with games like Dota 2, CS Go, PubG, and The Division.  The frames can range from 60FPS to 160FPS depending on the game and settings that you choose.  The system was tested using a 144Hz 27" Acer Monitor.



SteelSeries QCK Heavy Cloth Gaming Mouse Pad (Click Here)

SteelSeries Apex M750 RGB Mechnical Keyboard (Click Here)

Logitech G502 Proteus Spectrum RGB Tunable Gaming Mouse (Click Here)

HyperX Cloud II 7.1 Gaming Headset (Click Here)

El Gato Game Capture HD60 Pro for a Streaming Capture PC (Click Here)

Secretlab Premium Gaming Chairs (Click Here)

Make sure to subscribe to our page to receive notifications about new content, live streams, and giveaways!

Please contact us if you have any questions!

12replies Oldest first
  • Oldest first
  • Newest first
  • Active threads
  • Popular
  • no no no no no sirs, brothers sisters and all neighborhood,
    there's a big gimmick going on here,
    I spent all day to install 2x X5670 or 2x X5680 or 2x X5690 on a Z600 V1 tried every combination, nada!
    Top on it bought a second V1 to make sure nah! double nada!
    you can install single X5670 processor on CPU0 only, CPU1 does not accept a single X5670 or above

    One of the V1 came with 2x E5504 other one with 2x 5570 so they take 2 processors but I tried everything only I could install 1x X5670 
    on CPU0, also it is not possible to install a single X5680 or X5690 on v1, says heatsink is not highperformance.
    So please after all my headFword someone could you please show a BIOS picture that is possible to install 2x X5670 or above to Z600 V1, 
    that's a myth. 
    Says up to 2x X5675 processors for Z600 V1 in the forum I couldn't install 2x X5670 so how is that possible please show the picture of BIOS information, please.

    Also V1 takes PC3 12800U and PC3 10600U memory modules perfectly fine yes U, 12800U shows 1333MHz on BIOS

  • Also Z600 V1 does not support any kind of PC3L Low Voltage Modules 2Rx8 nor 2Rx2

  • Apologize, I just have installed 6x 8GB PC3L 12800R-11-13-B1 modules and they are working perfectly fine

  • So PC3L 12800R (Regestered) memory worked in your Z600 V1? Was your boot block date 1/05/09? I haven't tried low voltage regestered memory, but I get this error with PC3 10600R, http://prntscr.com/ry5szc .

  • sorry pal I've been moving house, I had only tried those microns (pictured, 4 of them 32GB) and they are compatible with V1 I don't care boot block date I just take picture of the serial, if it ends odd number-001 it's V1 even number-001 V2 that's easier to remind but I just tried 12800R SAMSUNG PC3L modules 8GB they did not work, if someone experienced have a look at the pictures proper maybe he will enlighten us. I am just an adventurist we need a PROFESSOOOOOOOOR!!!

    Also I did something mental with a V2 I will start a new topic :)))))

  • maybe stickers wrong, we need a PROFESSOOOOOOR

  • hello Rick, I just installed those mini 4GB PC3 R and PC3L R rams to V1, mixed. I think they called Value Ram, have you updated your BIOS?

  • It seems I have to agree with Frog Racer

    V1 460840-002 boards do NOT support 2x X5675 processors. Only one can be installed. As soon as you install a second one it will not boot or even show the bios boot screen and the fans will blast at full speed. Just a heads up for anyone else trying this even after updating the BIOS.

    The upgrade for my sons Z400 to a X5690 cpu worked perfectly however so thank you for that. 

    Have a nice day.

  • I been busy and haven't tried, but 2 x5570's work great.   Also, they are cheap.

  • But I haven't tried the PC3L 12800R Registered ram yet with the V1 board and 5570's.     HP states it wont work, but they have been wrong about a lot of things.

  • Hi Rick. Already ordered 2x X5570's on eBay. Indeed, cheap as chips. 8 euros for one. :D

  • Unless what was said previously above about PC3L ram actually works, you will need unbuffered U or ECC E ram.

Like1 Follow
  • 2 yrs agoLast active
  • 12Replies
  • 1019Views
  • 5 Following